Papan Dasar Kotak
Papan dasar galvanis hot-dip dengan set baut terbenam yang sesuai untuk fondasi.
- 100×100×8mm standard (50×50 / 120×120 options)
- Hole matched to D15–D26.5 rods
- Hot-stamped carbon steel
Aksesori Lainnya
Pelat dasar persegi, cincin pemegang plum, konektor formwork, mur cakram gunung, mur kombinasi dan penghubung, profil waling, set pin dan pendorong, kait pengembalian braket, dan perakitan batang pengikat tiga bagian.
Tidak semua komponen di lokasi proyek termasuk dalam satu sistem. Seri ini mengumpulkan cincin pemegang, pelat, konektor, dan aksesori yang secara praktis menghubungkan seluruh rangka formwork: pelat dasar persegi dan cincin pemegang plum untuk menyebar beban di bawah mur, konektor formwork untuk menyambung batang, mur cakram gunung dan mur kombinasi untuk ujung batang pengikat, mur penghubung untuk memperpanjang batang, profil waling, set pin dan pendorong, kait pengembalian braket, serta perakitan batang pengikat tiga bagian. Kontainer campuran dan ukuran khusus dapat dikirimkan sesuai permintaan.
Cincin Plum
Cincin plum (bergerigi) yang mengunci baut cakram melawan getaran.
- D15 / D20 tie rods
- Lobed thread-gripping profile
- Heat-treated spring steel
Kopling Bekisting
Kopling untuk menyambungkan pipa perancah dan tiang bekisting.
- Joins scaffold tubes and props
- Pressed steel construction
- Various tube diameters available
Mur Penghubung
Mur penghubung panjang untuk menyambungkan dua bagian batang pengikat.
- Joins two tie rod sections
- Fits D15 / D20 threads
- Extended thread engagement
Walers Formwork
Walers baja dengan lubang batang pengikat yang sudah diproduksi untuk formwork dinding.
- Twin 10#/12# channel welded construction
- 11.54 kN·m bending / 84.81 kN shear typical
- Pre-punched tie-rod holes
The parts that make the system fit together
This range covers what holds the main components in line: square base plates that spread nut load into soft concrete or timber, plum washers that resist loosening under vibration, couplers that join scaffold tube and prop lengths, waling profiles that carry the tie load along the wall, pin-and-wedge sets that lock corners, and 3-part tie assemblies for walls that must be made good after stripping. Individually they are small; missing, they stop a pour.
Sizes that actually match your rods
Plates and washers are only useful if the hole matches the rod: square base plates come 100×100×8 mm as standard with 50×50 and 120×120 mm options, with the hole matched to D15–D26.5 rods, flat or dome profile, hot-stamped carbon steel. Waling profiles are twin 10#/12# channel welded construction with a typical 11.54 kN·m bending capacity and 84.81 kN shear, pre-punched with tie-rod holes, in lengths 1.5–6 m. Couplers are pressed steel in slip or swivel type across the common tube diameters. State the rod diameter and the tube size when ordering rather than the part name alone.
Consolidate with the main order
Small parts are where a shipment becomes incomplete: a container of rods that arrives without the right plates delays the pour as surely as a missing clamp. We consolidate plates, washers, couplers and wedges into the same shipment as rods and nuts, packed by type in marked cartons on pallets. Stock sizes ship in about three days; waling profiles and cut-to-length items take 7–15 days. Send the full bill of materials and we will flag any part that does not match the rod or tube it is meant to fit before the order is confirmed.
FAQ Teknis
Aksesori Lainnya — Jawaban untuk Insinyur dan Pembeli
A formwork tie rod is a high-strength threaded bar that, together with nuts, anchor plates and walers, holds formwork panels against the lateral pressure of fresh concrete. It passes through the wall section and is either fully recovered after stripping (through-tie used with a sleeve) or permanently embedded (lost-end / water-stop type).