Papan Dasar Kotak
Papan dasar galvanisasi panas dengan set baut yang sesuai untuk fondasi.
- 100×100×8mm standard (50×50 / 120×120 options)
- Hole matched to D15–D26.5 rods
- Hot-stamped carbon steel
Aksesori Lain
Plat tapak segi empat, cincin plum, pemaut pembentuk, baut cakera gunung, baut gabungan dan sambung, profil papan pengikat, set pin dan kunci, hook balik sokongan dan persediaan rod ikat tiga bahagian.
Bukan semua komponen di tapak membentuk satu sistem. Kumpulan ini mengumpulkan cincin, plat, pemaut dan perkakas yang sebenarnya menyambung satu set pembentuk: plat tapak segi empat dan cincin plum untuk mengagihkan beban di bawah baut, pemaut pembentuk untuk menyambung bar, baut cakera gunung dan baut gabungan untuk hujung rod ikat, baut sambung untuk memanjangkan rod, profil papan pengikat, set pin dan kunci, hook balik sokongan, serta persediaan rod ikat tiga bahagian. Kuantiti campuran dan saiz tersuai ditawarkan mengikut permintaan.
Cincin Plum
Cincin plum (bergerigi) yang mengunci baut cakram terhadap getaran.
- D15 / D20 tie rods
- Lobed thread-gripping profile
- Heat-treated spring steel
Penyambung Acuan
Penyambung untuk menyambung tiub cerucuk dan sokongan acuan.
- Joins scaffold tubes and props
- Pressed steel construction
- Various tube diameters available
Nat Penyambung
Nat penyambung panjang untuk menyambung dua bahagian batang pengikat.
- Joins two tie rod sections
- Fits D15 / D20 threads
- Extended thread engagement
Walers Formwork
Walers baja dengan lubang pasak yang sudah diproduksi untuk formwork dinding.
- Twin 10#/12# channel welded construction
- 11.54 kN·m bending / 84.81 kN shear typical
- Pre-punched tie-rod holes
The parts that make the system fit together
This range covers what holds the main components in line: square base plates that spread nut load into soft concrete or timber, plum washers that resist loosening under vibration, couplers that join scaffold tube and prop lengths, waling profiles that carry the tie load along the wall, pin-and-wedge sets that lock corners, and 3-part tie assemblies for walls that must be made good after stripping. Individually they are small; missing, they stop a pour.
Sizes that actually match your rods
Plates and washers are only useful if the hole matches the rod: square base plates come 100×100×8 mm as standard with 50×50 and 120×120 mm options, with the hole matched to D15–D26.5 rods, flat or dome profile, hot-stamped carbon steel. Waling profiles are twin 10#/12# channel welded construction with a typical 11.54 kN·m bending capacity and 84.81 kN shear, pre-punched with tie-rod holes, in lengths 1.5–6 m. Couplers are pressed steel in slip or swivel type across the common tube diameters. State the rod diameter and the tube size when ordering rather than the part name alone.
Consolidate with the main order
Small parts are where a shipment becomes incomplete: a container of rods that arrives without the right plates delays the pour as surely as a missing clamp. We consolidate plates, washers, couplers and wedges into the same shipment as rods and nuts, packed by type in marked cartons on pallets. Stock sizes ship in about three days; waling profiles and cut-to-length items take 7–15 days. Send the full bill of materials and we will flag any part that does not match the rod or tube it is meant to fit before the order is confirmed.
Soalan Teknikal Lazim
Aksesori Lain — Jawapan untuk Jurutera dan Pembeli
A formwork tie rod is a high-strength threaded bar that, together with nuts, anchor plates and walers, holds formwork panels against the lateral pressure of fresh concrete. It passes through the wall section and is either fully recovered after stripping (through-tie used with a sleeve) or permanently embedded (lost-end / water-stop type).