Batang Tali Form D12
Batang tali semua-thread D12, 0.74 kg/m, ujian tegangan 35–42 kN mengikut bahan.
- D12 all-thread rod, 0.74 kg/m
- Tested tensile: A195 35 kN · 35K 42 kN (2026 catalogue)
- Length 200–8000mm, cut to length
Pasak dan Pasak Penghalang Air
Batang pengikat berkekuatan tinggi D15/17 dan D20/22 (gred 8.8/10.9), batang penghalang air lima-bahagian dan batang terbenam satu-bahagian, disertai data tegangan tarik dan pilihan salutan.
Batang pengikat merupakan komponen yang benar-benar menahan acuan. Siri ini merangkumi batang pengikat berkekuatan tinggi D15/17 dan D20/22, batang penghalang air lima-bahagian yang tidak hanya mengikat tetapi juga menyegel dinding, serta batang terbenam satu-bahagian untuk dinding di mana batang tidak boleh dikembalikan. Setiap halaman produk menyertakan data tegangan tarik tersendiri, pilihan salutan, serta cadangan pasangan sarung atau kon.
Pasak Kuat Tinggi D15/17
Pasak pemancang formwork kuat tinggi dalam D15/17, grade 8.8 / 10.9, oksida hitam atau galvanisasi.
- D15/17 all-thread rod (DW15, 17/10 thread), 1.47–1.50 kg/m
- Third-party tested tensile: Q235 100-110 kN · 45# 120-140 kN · 40Cr 140-160 kN · precision-rolled 180 kN (tested tensile, not allowable working load)
- Also available: D20/22 (2.60 kg/m, tested tensile 210-240 kN by material) — see D20/22 Form Tie Rod
Batang Tali Form D20/22
Batang tali semua-thread D20/22, 2.60 kg/m, ujian tegangan 210–240 kN mengikut bahan.
- D20/22 all-thread rod, 2.60 kg/m
- Tested tensile: Q235 210 kN · 45# 240 kN (2026 catalogue)
- Length 200–8000mm, cut to length
Batang pengikat gelek tepat
Benang gelek berterusan, tegangan diuji sehingga 180 kN, panjang mengikut pesanan.
- Precision rolled tie rod, thread rolled over the full length
- Nut can be positioned at any point along the rod
- Heavy formwork ties, including walls tied from one accessible face
Where through-tie rods are used
A tie rod is the member that actually resists the concrete pressure, so the choice follows the wall, not the catalogue. D12 (0.74 kg/m, tested tensile 35–42 kN) suits low-pressure walls, edge formwork and residential slabs. D15/17 (1.47–1.50 kg/m) is the volume choice for wall, column and slab formwork at normal pour heights. D20/22 (2.60 kg/m, tested tensile 210–240 kN by material) is specified where the pour rate, the height or the tie spacing pushes the load past what a 15 mm rod can hold — thick raft walls, bridge falsework, high single-lift pours.
How to size a tie rod for your drawing
Four values decide it: rod diameter, material grade, length and coating. Diameter comes from your engineer’s tie load; in D15/17 the "15" is the rod size and "17" is the width across flats of the matching nut, and the same rod is ordered in some markets as the 17/10 profile (17 mm outer thread × 10 mm pitch). Material sets the tested tensile: Q235 100–110 kN, 45# 120–140 kN, 40Cr 140–160 kN, precision-rolled 180 kN — all third-party tested tensile, not an allowable working load, so apply your own safety factor. Length is cut 200–8000 mm to your schedule. Coating follows exposure: plain for dry interior work, electro-galvanized for general site use, hot-dip galvanized 45–85 µm or Dacromet for outdoor, coastal or repeated-use formwork. Threads are rolled to DIN 976, A193 B7 or GB/T 15389, and we supply the matching cones, sleeves and nuts on the same order so the thread pair is never mismatched.
Lead time, paperwork and packing
Around 300 tonnes of standard sizes sit in stock at Yongnian, so plain and galvanized D15/17 and D20/22 in common lengths ship in about three days. Cut-to-length and non-standard thread or coating runs take 7–15 days. Mill certificates to EN 10204 3.1 are issued on request and are worth specifying for structural pours. Rods are bundled and strapped for container loading, with export packing to your instruction; mixed orders with nuts, cones and plates are consolidated into one shipment so site receives a complete tie set rather than a partial one.
Memilih dalam siri ini
Jika rekabentuk bentuk anda sudah menetapkan diameter rod, mulakan dengan rod kuat D15/D20 dan data tegangan mereka; jika dinding perlu kedap air, tiub penahan air lima bahagian menggantikan pengikat terus biasa tanpa mengubah jarak pengikat. Untuk perbandingan bersebelahan dua diameter, lihat perbandingan tiub D15 vs D20 kami. perbandingan tiub D15 vs D20
Soalan Teknikal Lazim
Pasak dan Pasak Penghalang Air — Jawapan untuk Jurutera dan Pembeli
D15 and D20 are nominal bar diameters. At the same property class the tensile capacity scales with the cross-sectional area, so D20 carries roughly 1.7 to 1.8 times the load of D15. D15 suits residential slabs and light walls; D20 is used for thicker walls, faster pour rates and higher hydrostatic pressure. The choice is always confirmed against the formwork pressure calculation for the actual pour height and rate, not copied from a previous job.