Batang pengikat gelek tepat
Benang gelek berterusan, tegangan diuji sehingga 180 kN, panjang mengikut pesanan.
Langsung dari Pabrik
CNC Sendiri
Laporan QC Batch
OEM ke Gambar
1 / 3Pasak dan Pasak Penghalang Air
Batang pengikat gelek tepat
A precision rolled tie rod: the thread is rolled over the full length instead of being cut, so the section stays continuous and a nut can be set anywhere along the rod. It is used where a heavy formwork tie runs through a wall and has to be tensioned from the accessible face, and where the same rod also serves as a prestressing bar by design. Supplied in 40Cr and PSB830/PSB930 grades; diameters, lengths and end treatment follow your drawing.
Spesifikasi
- Precision rolled tie rod, thread rolled over the full length
- Nut can be positioned at any point along the rod
- Heavy formwork ties, including walls tied from one accessible face
- Cut to length on your drawing; diameters on request
Harga diberikan berdasarkan spesifikasi produk, bahan/grade, kuantiti, destinasi dan keadaan pasaran semasa. Hubungi kami untuk penawaran terkini.
Penawaran yang ditinjau oleh insinyur dalam 24 jam.
Spesifikasi Teknis
| Material | 40Cr / PSB830 / PSB930 |
| Thread | Continuous rolled thread, full length |
| Surface | Black / zinc plated |
Bahan40Cr / PSB830 / PSB930
Finishing PermukaanBlack · Zinc plated
Beban TerukurInquire
Berat UnitInquire
PengemasanBundled on pallet
Proses Produksi
01
02
03
04
05
06Jelaskan Grade Bahan
| Grade | Catatan |
|---|---|
| Q235 | Plain carbon steel. Economic option for light and medium formwork loads. Not heat treated. |
| 45# | Medium carbon steel. The standard formwork tie rod grade in China; quenchable to class 8.8. |
| 40Cr | Alloy steel. Higher hardenability and better fatigue performance than 45#; used where repeated reuse matters. |
| Class 10.9 bolt | Quenched and tempered alloy steel bolt used in the climbing cone set. Not electroplated without a documented baking cycle. |
| QT450-10 | Ductile (nodular) iron with 450 MPa tensile and 10% elongation. Used for sleeves and embedded plates where toughness and castability matter. |
| HRB400 | Hot-rolled ribbed bar (threaded steel) to Chinese standard. Used for embedded foot bolts; good bond with concrete. |
Aplikasi
Panduan Pembelian
- Confirm the required load and the matching nut thread
- Specify diameter, steel grade and cut length
- State the end treatment: cut, chamfered, or fitted with a coupling sleeve
Informasi Pembelian
- OEM / Kustom
- Gambar atau label sendiri diterima
- MOQ
- Pesanan percobaan OK · SKU campuran diterima
- Waktu Pengiriman
- Stok 3 hari · Kustom 7-15 hari
- Pengemasan
- Tahan Laut: palet + ikat tali + tahan air
- Pembayaran
- T/T · L/C saat tiba
- Incoterms
- FOB Tianjin · CIF · CFR · EXW
Bacaan Teknis Terkait
Produk Terkait
Soalan Teknikal Lazim
Batang pengikat gelek tepat — Jawapan untuk Jurutera dan Pembeli
It consists of two reusable outer threaded bars, two plastic cones and one embedded middle bar with a welded water-stop plate. After stripping, the two outer bars are unscrewed and reused on the next pour; only the middle section stays inside the wall. This keeps consumable cost low while producing a watertight wall penetration.