Baut Terbenam Formwork Satu Sisi
Baut terbenam untuk formwork satu sisi dan dinding penahan.
Langsung dari Pabrik
CNC Sendiri
Laporan QC Batch
OEM ke Gambar
1 / 3Baut, Cincin dan Aksesori
Baut Terbenam Formwork Satu Sisi
Embedded before pouring, the J-hook (dimensioned as diameter × length × hook width × hook length × thread) transfers formwork load into the cured concrete for single-sided concreting and foundation anchors. Supplied with positioning templates, anchor plates and full inspection documentation; hot-dip galvanized for long-term embedment.
Spesifikasi
- J / L hook embedded anchors
- Diameter 12–36mm, custom length
- Positioning template included
- Anchor plate and nut options
- HDG finish for embedment
Harga diberikan berdasarkan spesifikasi produk, bahan/grade, kuantiti, destinasi dan keadaan pasaran semasa. Hubungi kami untuk penawaran terkini.
Penawaran yang ditinjau oleh insinyur dalam 24 jam.
Spesifikasi Teknis
| Type | J / L hook or straight with plate |
| Diameter | 12–36mm |
| Embedment | Per project drawing; min. spacing/edge per design code |
| Template | Steel positioning template for bolt group |
| Finish | Hot-dip galvanized (45–85µm) or plain |
| Packaging | Kits with template, nuts and washers |
BahanHRB400 hot-rolled ribbed bar (threaded steel)
Finishing PermukaanPlain (black) · Zinc plated on request
Beban Terukur250 kN rated
Berat UnitD25 × 700 mm: 2.4 kg per piece
PengemasanSet-packed with matched accessories · marked per set
Proses Produksi
01
02
03
04
05
06Jelaskan Grade Bahan
| Grade | Catatan |
|---|---|
| Q235 | Plain carbon steel. Economic option for light and medium formwork loads. Not heat treated. |
| 45# | Medium carbon steel. The standard formwork tie rod grade in China; quenchable to class 8.8. |
| 40Cr | Alloy steel. Higher hardenability and better fatigue performance than 45#; used where repeated reuse matters. |
| Class 10.9 bolt | Quenched and tempered alloy steel bolt used in the climbing cone set. Not electroplated without a documented baking cycle. |
| QT450-10 | Ductile (nodular) iron with 450 MPa tensile and 10% elongation. Used for sleeves and embedded plates where toughness and castability matter. |
| HRB400 | Hot-rolled ribbed bar (threaded steel) to Chinese standard. Used for embedded foot bolts; good bond with concrete. |
Aplikasi
Panduan Pembelian
- Send anchor layout drawing for bolt group template design
- Confirm embedment depth and edge distances with the engineer
- Request pull-out test data for project submittals
- For permanent embedment, require HDG or stainless
Informasi Pembelian
- OEM / Kustom
- Gambar atau label sendiri diterima
- MOQ
- Pesanan percobaan OK · SKU campuran diterima
- Waktu Pengiriman
- Stok 3 hari · Kustom 7-15 hari
- Pengemasan
- Tahan Laut: palet + ikat tali + tahan air
- Pembayaran
- T/T · L/C saat tiba
- Incoterms
- FOB Tianjin · CIF · CFR · EXW
Produk Terkait
Soalan Teknikal Lazim
Baut Terbenam Formwork Satu Sisi — Jawapan untuk Jurutera dan Pembeli
A formwork tie rod is a high-strength threaded bar that, together with nuts, anchor plates and walers, holds formwork panels against the lateral pressure of fresh concrete. It passes through the wall section and is either fully recovered after stripping (through-tie used with a sleeve) or permanently embedded (lost-end / water-stop type).