Batang Pengikat D12
Batang ulir penuh D12, 0,74 kg/m, uji tarik 35–42 kN berdasarkan material.
Langsung dari Pabrik
CNC Dalam Pabrik
Laporan Pengujian Batch
OEM Berdasarkan Gambar
1 / 1Batang Pengikat & Batang Pengikat Penghalang Air
Batang Pengikat D12
D12 all-thread form tie rod at 0.74 kg/m, produced on CNC thread-rolling lines for burr-free threads and consistent geometry. Tested tensile capacity by material: A195 35 kN and 35K 42 kN (2026 catalogue data). Cut to length from 200mm to 8000mm, supplied plain, electro-galvanized, hot-dip galvanized or Dacromet.
Spesifikasi
- D12 all-thread rod, 0.74 kg/m
- Tested tensile: A195 35 kN · 35K 42 kN (2026 catalogue)
- Length 200–8000mm, cut to length
- A195 / 35K alloy steel
- Plain, electro-galvanized, HDG or Dacromet
Harga ditawarkan berdasarkan spesifikasi produk, material/grade, jumlah, tujuan, dan kondisi pasar saat ini. Hubungi kami untuk penawaran terbaru.
Penawaran yang ditinjau oleh insinyur dalam 24 jam.
Spesifikasi Teknis
| Thread | D12 all-thread |
| Load Rating | Tested tensile 35 kN (A195) / 42 kN (35K) |
| Grades | — |
| Material | A195 / 35K alloy steel |
| Length | 200–8000mm, custom cut-to-length |
| Surface | Plain, electro-galvanized (8–25µm), HDG (45–85µm), painted, Dacromet |
| Packaging | Bundled on pallet, VCI wrap, seaworthy cartons |
BahanA195 · 35K alloy steel
Finishing PermukaanPlain (black) · Electro-galvanized · Hot-dip galvanized · Dacromet
Beban TerukurTested tensile: A195 35 kN · 35K 42 kN (2026 catalogue)
Berat Unit0.74 kg/m
PengemasanBundled on pallet · VCI wrap · seaworthy cartons · marked per BOM
Proses Produksi
01
02
03
04
05
06Jenis Bahan Dijelaskan
| Grade | Catatan |
|---|---|
| Q235 | Plain carbon steel. Economic option for light and medium formwork loads. Not heat treated. |
| 45# | Medium carbon steel. The standard formwork tie rod grade in China; quenchable to class 8.8. |
| 40Cr | Alloy steel. Higher hardenability and better fatigue performance than 45#; used where repeated reuse matters. |
| Class 10.9 bolt | Quenched and tempered alloy steel bolt used in the climbing cone set. Not electroplated without a documented baking cycle. |
| QT450-10 | Ductile (nodular) iron with 450 MPa tensile and 10% elongation. Used for sleeves and embedded plates where toughness and castability matter. |
| HRB400 | Hot-rolled ribbed bar (threaded steel) to Chinese standard. Used for embedded foot bolts; good bond with concrete. |
Aplikasi
Panduan Pembelian
- Confirm diameter, material and required tensile load with your structural engineer
- Match nuts, cones and sleeve threads to the rod before ordering
- Request mill certificates (EN 10204 3.1) for structural applications
Informasi Pembelian
- OEM / Kustom
- Gambar atau label sendiri diterima
- MOQ
- Pesanan percobaan OK · SKU campuran diterima
- Waktu Pemesanan
- Stok 3 hari · Kustom 7-15 hari
- Pengemasan
- Tahan Laut: palet + ikatan + tahan air
- Pembayaran
- T/T · L/C saat ini
- Incoterms
- FOB Tianjin · CIF · CFR · EXW
Bacaan Teknis Terkait
Produk Terkait
FAQ Teknis
Batang Pengikat D12 — Jawaban untuk Insinyur dan Pembeli
It consists of two reusable outer threaded bars, two plastic cones and one embedded middle bar with a welded water-stop plate. After stripping, the two outer bars are unscrewed and reused on the next pour; only the middle section stays inside the wall. This keeps consumable cost low while producing a watertight wall penetration.